"oscillator-startup"-tagged Public Circuits

Now showing circuits 1-4 of 4. Sort by recently modified name

	joule thief 01 PUBLIC Joule Thief circuit. CL have changed something in the simulator because this used to run with the sim set up as. Now, it does not show the exponential rise of V1 and does not start oscillating unless... by signality | updated July 01, 2014 initial-conditions   joule-thief   oscillator-startup   startup
	MOSFET Royer-like oscillator 01 PUBLIC V1 (vcc) has exponential ramped startup to kick-start oscillation. XFRMR1 forms a centre tapped inductor However, CL takes a long time to run the simulation. Simulate > Time Domain > Run Time-Domain... by signality | updated March 01, 2013 initial-conditions   oscillator   oscillator-startup   royer   startup   time-step
	relaxation osc fixed 02 PUBLIC Sometimes you have to kick an oscillator out of an initial, metastable state so that it starts reliably at a user defined time in the simulation. This shows a way to do that. by signality | updated April 10, 2012 initial-conditions   oscillator-startup   startup
	relaxation osc fixed 03 PUBLIC Sometimes you have to kick an oscillator out of an initial, metastable state so that it starts reliably at a user defined time in the simulation. This shows a way to do that. by signality | updated April 10, 2012 initial-conditions   oscillator-startup   startup

More tags

555   7805   ac-to-dc   active-filter   amplifier   analog   and   anode   attenuator   atx   audio   automotive   band-reject   bandgap   behavioral   bias-point   bjt   bode   bridge-rectifier   button   calculator   cascaded-filters   cascode   cathode   cmos   colpitts   compensation   constant-current-source   current-limiting   current-mirror   current-monitor   current-regulator   dac   dc-to-ac   device-modeling   differential   differentiator   digital   diode   divider   emitter-follower   feedback   filter   flyback   flyback-diode   frequency-domain   full-wave   guitar   ham-radio   high-pass   high-speed   high-voltage   hv   hysteresis   ic   ignition-coil   induction   inductive   inductive-load   initial-conditions   instrumentation-amplifier   integrator   inverting   jfet   laplace   led   led-array   level-shift   lighting   lipo   lm317   load-cell   logic-gate   low-pass   mechanical   microcontroller   microphone   mosfet   motor   multivibrator   non-inverting   nonlinear   nor   notch   ohms-law   op-amp   optical   or   oscillator   parallel   passive   passive-filter   pcb-design   phase-shift   photodiode   photoresistor   phototransistor   piezo   plants   potentiometer   power   power-supply   power-supply-unit   preamp   pull-down   pull-up   pwm   rc   relaxation-oscillator   relay   resistor-ladder   resonance   rf   rlc   rom   saturation   schmitt-trigger   sensor   series   servo-motor   signal   spark-plug   stability   stepper   summing   superposition   switching   time-constant   transformer   transistor   translinear   twin-t   voltage-divider   voltage-regulator   waveform-arithmetic   wiring   xnor   xor   zener-diode   zero-voltage-switching  

---

New @ CircuitLab
johnbreslin saved circuit: "First Order Low Pass Filter"
yohannathomas22 answered: "Microcontroller problem" 4 hours ago
farahmand saved circuit: "SimpleRC"
Rumaldog saved circuit: "Seat belt Alarm System"
Pyriel saved circuit: "Seat Belt Alarm System"
nboucquey asked: "The Drag and Drop not working on..."
Jiminvan replied to discussion: "Help needed - trying to simulate an..."
Hismandent commented on question: "9V to 5V conversion problems"
BeverlyJClark answered: "9V for ATmega328P?"
vanderghast commented on question: "9V to 5V conversion problems"
R1ckRul3s asked: "Crystal Oscillator Circuit: DC/AC..."
hank2000 answered: "H-bridge for bistable solenoid"
dominica answered: "Led chaser power issue"
hank2000 asked: "H-bridge for bistable solenoid"
Lionsio asked: "9V to 5V conversion problems"
detailsizzling commented on an answer to: "How to Design a Circuit for..."
natastro started discussion: "Photodiode symbol: messed-up arrow"
krokoi commented on question: "how to represent a symetrical..."
b3organ replied to discussion: "Export a Parts list"
Jogibaer replied to discussion: "Vacuum Tube Models"
CircuitLab Blog: "Live DC Simulation!"
CircuitLab Blog: "Digital Adders and Wider Muxes"